Greetings, dear inquisitive readers! Today we will find out how to disable the message “Windows has detected a hard drive problem.” Usually such an expletive actually indicates problems with your hard drive. In my case, it appeared after installing Windows on a hard drive with a certain number of bad blocks and an unacceptably large value of attribute No. 5 (Reallocated Sectors Count) in SMART. We will look at how to check a hard drive for errors separately, but now we’ll just turn off this window so that it doesn’t interfere with work with its sudden appearances. Nevertheless, as soon as the opportunity arises, I recommend replacing the hard drive with a new one.

Let's go to the Group Policy Editor. To do this, press Win + R and write: gpedit.msc.

The Local Group Policy Editor will open. Let's go to the address: Computer configuration -> Administrative Templates -> System-> Diagnostics -> Disk diagnostics.

There we will find two parameters that we will deal with. Double-click on the first parameter and in the next window set the value to Disable. Click OK.

If the system displays the error “Windows has detected a hard drive problem,” the reasons for this can be very different, as well as its consequences. The hard drive may be faulty (or defective if the computer is new), or the operating system files are damaged and will not load. If you encounter such a problem, I hasten to warn you - you can lose all your data: documents, videos, programs and images if the disk eventually becomes unusable, which will happen sooner or later.

What to do if you receive the message “Windows has detected a hard drive problem”

First, stay calm, don't panic. Pay attention to the bottom of the message, which shows which sections are having problems. This will save you time, given that the check takes a lot of time - you will know which sections to work with. We will perform the check using the CHKDSK command (from Check Disk), which checks the status of the hard drive and corrects any errors or problems, if possible.

And the warning “Windows has detected a hard drive problem,” as mentioned above, occurs due to hard drive problems - and sometimes it’s just sector damage, which can be cured using CHKDSK. So, we will perform the check through the command line, which can be opened by simultaneously pressing the Windows + R keys.

The Run dialog box opens. Type CMD and press Enter.

In the command prompt window, enter the letter of the problematic partition, or leave it as is if you need to check the default disk partition.

However, we see the message "ATTENTION! Parameter F is not specified. CHKDSK runs in read-only mode", plus some information. This is not enough. If we want to perform a full scan of the hard drive and allow Windows to automatically fix system file errors and bad sectors, we need to add the /F parameter to the CHKDSK command, i.e. so that it becomes CHKDSK /F.

Note: If you selected a disk containing an operating system to scan, you will be prompted to scan after rebooting.

If the CHKDSK command did not help

In such a situation, I recommend that you start creating backup copies of all important files and data. You can transfer them to safe partitions from partitions that have faults (remember, the problem partitions were indicated in the warning). Or to another medium, for example, a portable hard drive.

Once you have copied all your important data, you can check the hard drive to see if it is suitable for further use. Those. you can try to restore it to its functionality by full (not quick) right-clicking on the disk and selecting “Format” - the process may take quite a long time, depending on the size of the disk. Have patience.

All the above tips and instructions should help you in solving the “Windows has detected a hard drive problem” error related to hard drive problems. Also, in addition to all of the above, I would advise you to reinstall the operating system, because in most cases this helps in solving most problems. If all else fails, please give me feedback via the comment form below.

What to do if Windows detects hard drive problems?

Sometimes users encounter an unexpected problem when they suddenly see a system message informing them that the system has detected a hard drive problem. Almost every user then falls into a stupor and does not know what to do next. We will look at the 3 most common causes of this error, and tell you what to do in each of these situations.

You may lose all your programs, data, documents, videos, music and important images when your hard drive eventually fails. Note the partition of the disk that is failing and the one that is not.

• Your hard drive is not working and may die sooner or later.
• You may experience freezes and not respond to the error.
• Firstly, don't panic, stay calm.
• How much and other useful information.

You can try them one by one to fix the error in your case with success. A bad sector is an area on the hard drive that cannot store information. Correcting file errors takes longer than reporting, and correcting file errors and bad sectors takes even longer. See the Troubleshooting section at the end of this section. This section covers the most commonly used aspects of Chkdsk.

You can also disable the appearance of the most problematic message “Windows has detected a hard drive problem” by changing the corresponding system registry setting. To do this, it will be enough to follow the steps indicated in this video:

It is advisable to select "Scan" and try to recover bad sectors to physically check the surface of the hard drive. However, this step increases the time it takes to complete the scan. Using the graphical user interface.

You may be prompted to scan the next time you restart your computer. Using the command line interface. This error message indicates that the hard drive is no longer safe to store data and there is a need to back up your data before it is lost forever. What causes this error?

At the same time, I would advise you not to rush to disable this message, as it is an important indicator of the health of your hard drive and the operating system as a whole;

• Check the integrity of your OS registry using special utilities such as CCleaner, RegCleaner and analogues;
• Take care of cooling your hard drive. In some cases, the appearance of bad sectors was caused by overheating of the hard drive. Use special cooling pads with a built-in cooling system to avoid overheating of the hard drive.

Conclusion

The most common cause of the error “Windows has detected a hard drive problem” is the collapse of the hard drive, with the latter gradually failing. In this case, it is recommended that the first step is to make a copy (backup) of the necessary files on this disk. Standard hard disk check. What to do if Windows detects problems with your hard drive. What to do if Windows detects hard drive problems

A number of Windows operating system users may encounter the system message “Windows has detected a hard drive problem.” If you skip this message, it appears again, and the frequency of its appearance increases over and over again. In this article I will tell you how to fix the error - Windows has detected a hard drive problem, what are the causes and symptoms of this problem, and how to fix it.

What does the message “Windows has detected a hard drive problem” mean?

The main attribute of this dysfunction is the message “Windows has detected a hard drive problem” that appears, as well as the system’s offer to immediately begin the process of archiving existing data. This problem occurs on almost all modern operating systems of the Windows family, from Windows XP to Windows 10.

Moreover, this message usually appears not just once, but over and over again, forcing the user to start thinking about a Windows error in which hard drive problems were detected.

Typically, this message is a litmus test for serious problems on the hard drive, such as:

• The hard drive is crumbling and will soon stop working altogether;
• The information on the hard drive will soon be lost forever;
• The system files on such a disk are seriously damaged, and soon the system will no longer boot at all;
• The computer will slow down and freeze, take a very long time to load, and will soon stop responding to user commands.

Causes of the problem

Before we consider the solution to the “Windows has detected a hard drive problem” error, we need to determine the causes of this dysfunction. They are as follows:

How to fix the error when Windows detected problems with the HHD disk

So, how to fix the “Windows has detected a hard drive problem” error? I recommend doing the following:

If problems are observed on the “c” drive, and it is your system drive, then the chkdsk utility will suggest checking it the next time the system starts. Agree with the proposal by clicking on “Y”, reboot the system, and wait while the utility checks your disk for errors.

• Perform a hard drive surface test. Among the various programs recommended for these purposes, I would highlight the free MiniTool Partition Wizard application (other alternatives, such as MHDD or HDAT2, can also be mentioned). Download, install and run the specified application, right-click on the problem drive (usually system C:\), and select the “Surface Test” option. Then click on “Start now”. The program will analyze the surface of the hard drive; the more errors there are, the more “red” blocks you will see in the program’s graphic window.

As for the already mentioned MHDD, you can also take advantage of its functionality by analyzing the disk surface in REMAP mode.

You can also disable the appearance of the most problematic message “Windows has detected a hard drive problem” by changing the corresponding system registry setting. To do this, it will be enough to follow the steps indicated in this video:

At the same time, I would advise you not to rush to disable this message, as it is an important indicator of the health of your hard drive and the operating system as a whole;

• Check the integrity of your OS registry using special utilities such as CCleaner, RegCleaner and analogues;
• Take care of cooling your hard drive. In some cases, the appearance of bad sectors was caused by overheating of the hard drive. Use special cooling pads with a built-in cooling system to avoid overheating of the hard drive.

Conclusion

The most common cause of the error “Windows has detected a hard drive problem” is the collapse of the hard drive, with the latter gradually failing. In this case, it is recommended that you first make a copy (backup) of the necessary files on this disk (some make a copy in the form of an image of the entire hard drive), and only then carry out the entire set of actions described above. If the problems with the disk are random, then the system utilities chkdsk and sfc will restore the functionality of your hard drive, guaranteeing its stable operation in the future.

In contact with